; ±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±± ; ³ ACiDView 3.03 Configuration (.CFG) file - ACiD Productions(tm) 1994 ³ ; ³ See ACiDVIEW.NFO for more information ³ ; ±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±± ;ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Notes ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ; The format of the commands below MUST be left as it is. You should only ; modify the information after the : mark, or after the = mark if it ; is a toggle. ;ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Start Up Config ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ RESOLUTION=TEXT ; The resolution ANSI and BIN are displayed in ; TEXT, XGA, VGA, SVGA1, SVGA2, SVGA3, SVGA3 BAD MODES: :END BAD MODES ; List of RESOLUTIONs not to be used ; XGA, VGA, SVGA1, SVGA2, SVGA3, SVGA4 iCE COLOR=OFF ; Determines if ANSI and BIN blinks or allows 16 background colors, ; aka iCE Color. If ON, blinking is not possible. ;ON, OFF COLOR=COLOR ; What coloring to use for ANSI and BIN ; COLOR = Full color ; GREY = Grey scale ; ASCII = No color ; COLOR, GREY, ASCII ASPECT RATIO=25 ; How ANSI and BIN "look" ; 25 = Looks like 25x80 text mode ; 50 = Looks like 50x80 text mode ; 25, 50 WIDE=OFF ; If turned on ANSI and BIN are scaled up by about 2X when graphicly ; interpreted ; ON, OFF VIEWING=READ ; Determines how ANSI is viewed ; READ = Interpreted then displayed ; VIEW = Displayed as it is interpreted (ANSImation) ; VIEW, READ TAGGING=SHOW ; Determines what file tagging is used for ; SHOW = Slide show ; DUAL = Dual mode (See ACIDVIEW.NFO for more information) ; SHOW, DUAL BPS=OFF ; BPS rate to simulate during ANSI and RIP display, must be in VIEW ; mode to use with ANSI ; OFF, # MASK=*.* ; Used to "filter" the files shown. 1 mask allowed. EXCLUDE: ARJ COM DRV EXE HLP LZH MOD S3M WAV ZIP :END EXCLUDE ; List of extensions to be excluded from file listings and command line ; operation BOUNCE=ON ; Whether or not BIN viewing in TEXT mode bounces when the edge is reached ; ON, OFF ;ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Misc. Configuration ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ FONT DIR=.\FONTS ; Where the BGI fonts are located (.CHR files.) ; >>>>>>>>>>>>>>>>>>>THIS IS VITAL IF YOU WANT TO VIEW RIP<<<<<<<<<<<<<<<<<< B. SMOOTH=100 ; Accuracy of Benzier Curve generation. Lower values are faster, however ; less accurate (can cause problems with flood filling.) If you have a slow ; processor, this value is worth playing with, but if you have a Pentium ; just set it to 200 and don't worry about it. ; 1 - 200 SVGA=AUTO ; Used to configure the SVGA routies ; AUTO = Auto detect SVGA chipset ; NONE = No SVGA card present ; VESA = Use VESA extended BIOS ; 1 = VESA BiOS ; 2 = Ahead "A" type ; 3 = Ahead "B" type ; 4 = ATI 18800 ; 5 = ATI 18800-1 ; 6 = ATI 28800 ; 7 = Chips & Technologies 82c451/455/456 ; 8 = Chips & Technologies 82c452 ; 9 = Chips & Technologies 82c453 ; 10 = Genoa 600 series ; 11 = Oak OTi-O67 ; 12 = Paradise PVGAla ; 13 = Paradise WD90C00/WD90C10 ; 14 = Paradise WD90C11 ; 15 = Trident 8800 ; 16 = Trident 8900 ; 17 = Tseng ET3000 ; 18 = Tseng ET4000 ; 19 = Video 7 ; 20 = Cirrus Logic 54OO series ; 21 = S3 ; 22 = Trident 89OOB/89OOC ;NONE, AUTO, VESA # MULTIFRIENDLY=ON ; Whether to use the quick and simple interface and disable BPS simulation ; Automaticly turned on if using a multi-tasker ; ON, OFF LOG DIRECTORY=ON ; This is the toggle for ACiD View to load directories into the file listing. ; OFF = no directory changing will be available. ; ON, OFF LOG DRIVE=ON ; This is the toggle for ACiD View to load drives into the file listing. ; OFF = no drive changing will be available. ; ON, OFF ; ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ END OF ACiDVIEW.CFG ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ